SKALAR® X3000®

The high-performer for high-strength materials

  • Product level 3
  • Hook tooth
  • Solid materials
  • Band width 27 x 0.9 - 100 x 1.6mm
    Band width 1-1/16 x 0.035 - 4 x 0.063 Inch

 

Request a quote

SKALAR® X3000® — The high-performer for high-strength materials

The modified X3000® cutting material enables high-strength materials and special alloys to be cut precisely. This cutting material, available exclusively from WIKUS, combines even higher tooth tip hardness and wear resistance with excellent toughness compared to the M42 cutting material.

In combination with the carrier band made of alloyed tempering steel, the SKALAR® X3000® bimetal band saw blade achieves outstanding continuous operation properties.


Application

  • High cutting performance with high-alloy austenitic materials
  • Continuous operation on large sawmills and on large blocks
  • Especially for mixing programs with a large material mix
  • Also for difficult-to-machine non-ferrous special alloys
  • ESU material, materials above 1000 N/mm2 tensile strength
     

Advantages

  • High productivity due to excellent cutting rates
  • Lower cutting forces, smooth running, and straight cutting surfaces
  • Optimal tip geometry for chip division
  • Fewer blade changes due to increased blade-life
     

Features

  • Ground contour with specially matched tooth pitch
  • Tooth edge made of the cutting material X3000 ® with positive rake angle
  • Special set for optimal chip division
  • High hardness, wear resistance and toughness due to the cutting material X3000®
     

As with all SKALAR® band saw blades, the high cutting performance of the SKALAR® X3000® band saw blade is based not only on the special properties of the cutting material, but also on the specially adjusted tooth geometry, a slightly increased positive rake angle and the optimum setting sequence.

In addition, an increase in stability in the backing material supports high blade-life, especially when sawing difficult-to-machine, high-alloy materials such as quenched and tempered, annealed, carbon steels with tensile strengths greater than 1000N/mm².


Dimensions

Tooth pitch in ZpZ

Width x thickness
mmInch
27 x 0.901-1/16 x 0.035
34 x 1.101-3/8 x 0.042
41 x 1.301-5/8 x 0.050
54 x 1.302-1/8 x 0.050
54 x 1.602-1/8 x 0.063
67 x 1.602-5/8 x 0.063
80 x 1.603-1/8 x 0.063
100 x 1.604 x 0.063
Contact length[mm][Inch]
 
2.5-3.41.8-2.51.4-1.81.2-1.61-1.40.7-1
K
KK
KKK
K
KKKKK
KKKKK
KKKK
K
100-2203.9-8.7180-3507.1-13.8300-60011.8-23.6400-70015.7-27.6500-100019.7-39.4900-200035.4-78.7
K = Hook tooth

  • Nickel-based alloys
  • Titanium / titanium alloys
  • Tempered steels (over 1000 N/mm² / 32 HRC)
  • Rust-proof and acid-resistant steels (austenitic)
  • Duplex and heat-resistant steels
  • Aluminium bronzes

Any more questions?

The experts of our Technical Competence Center are happy to help you answer further technical questions connected to band selection and use.

Current website / language

Other websites

WIKUS FRANCE S.A.S.
WIKUS SIERRAS CINTAS S. de R. L. De C.V
WIKUS Nordic AB
WIKUS AUSTRIA GmbH
WIKUS Saw Technology, Corp
WIKUS Canada Ltd.
WIKUS Saw Technology (Shanghai) Co. Ltd
WIKUS India Pvt. Ltd.