SKALAR® X3000®
The high-performer for high-strength materials
Product level 3
Hook tooth
Solid materials
Band width 27 x 0.9 - 100 x 1.6mmBand width 1-1/16 x 0.035 - 4 x 0.063 Inch
Add to watchlistAdded to watchlist
has been added to the watchlist.
View watchlisthas been removed from the watchlist.
View watchlist
SKALAR® X3000® — The high-performer for high-strength materials
The modified X3000® cutting material enables high-strength materials and special alloys to be cut precisely. This cutting material, available exclusively from WIKUS, combines even higher tooth tip hardness and wear resistance with excellent toughness compared to the M42 cutting material.
In combination with the carrier band made of alloyed tempering steel, the SKALAR® X3000® bimetal band saw blade achieves outstanding continuous operation properties.
Application
- High cutting performance with high-alloy austenitic materials
- Continuous operation on large sawmills and on large blocks
- Especially for mixing programs with a large material mix
- Also for difficult-to-machine non-ferrous special alloys
- ESU material, materials above 1000 N/mm2 tensile strength
Advantages
- High productivity due to excellent cutting rates
- Lower cutting forces, smooth running and straight cutting surfaces
- Optimal tip geometry for chip division
- Fewer blade changes due to increased blade-life
Features
- Ground contour with specially matched tooth pitch
- Tooth edge made of the cutting material X3000 ® with positive rake angle
- Special set for optimal chip division
- High hardness, wear resistance and toughness due to the cutting material X3000®
As with all SKALAR® band saw blades, the high cutting performance of the SKALAR® X3000® band saw blade is based not only on the special properties of the cutting material, but also on the specially adjusted tooth geometry, a slightly increased positive rake angle and the optimum setting sequence.
In addition, an increase in stability in the backing material supports high blade-life, especially when sawing difficult-to-machine, high-alloy materials such as quenched and tempered, annealed, carbon steels with tensile strengths greater than 1000N/mm².
Dimensions
Tooth pitch in tpi
| Width x thickness | |
|---|---|
| mm | Inch |
| 27 x 0.90 | 1-1/16 x 0.035 |
| 34 x 1.10 | 1-3/8 x 0.042 |
| 41 x 1.30 | 1-5/8 x 0.050 |
| 54 x 1.30 | 2-1/8 x 0.050 |
| 54 x 1.60 | 2-1/8 x 0.063 |
| 67 x 1.60 | 2-5/8 x 0.063 |
| 80 x 1.60 | 3-1/8 x 0.063 |
| 100 x 1.60 | 4 x 0.063 |
Contact length[mm][Inch] | |
| 2.5 - 3.4 | 1.8 - 2.5 | 1.4 - 1.8 | 1.2 - 1.6 | 1 - 1.4 | 0.7 - 1 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| K | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| K | K | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| K | K | K | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| K | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| K | K | K | K | K | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| K | K | K | K | K | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| K | K | K | K | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| K | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 100-2203.9-8.7 | 180-3507.1-13.8 | 300-60011.8-23.6 | 400-70015.7-27.6 | 500-100019.7-39.4 | 900-200035.4-78.7 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
K = Hook tooth
- Nickel-based alloys
- Titanium / titanium alloys
- Tempered steels (over 1000 N/mm² / 32 HRC)
- Rust-proof and acid-resistant steels (austenitic)
- Duplex and heat-resistant steels
- Aluminium bronzes
has been added to the watchlist.
View watchlisthas been removed from the watchlist.
View watchlistAny more questions?
The experts of our Technical Competence Center are happy to help you answer further technical questions connected to band selection and use.
Deutsch
English
Français
Italiano
Español
日本語
中国的